How To Install Deck Wheel Kit On Troy Bilt Pony

If you've e'er endemic a lawn tractor you've probably dealt with the result of a broken belt. It'south a frustrating trouble that can exist difficult to repair -- until at present. In this article, nosotros'll help walk you lot through the time consuming procedure of replacing bulldoze belts on a Troy-Bilt Pony lawn tractor. We've broken downwards each footstep to brand information technology as simple equally possible. Follow each department in this commodity and refer to the video to get this tough repair completed, without visiting a repair shop.

Demand Troy-Bilt Pony parts? We've got all of the parts featured in this article and more on our Pony parts page. Removing the deck

one. Lower the deck to its lowest position

Use your tractors lever to move the mower deck to its lowest position.

2. Remove the belt baby-sit

Use a socket wrench to unscrew this from the bottom of the mower.

three. Remove the belt from the pulley

It should be hands removed from the pulley with your hands.

four. Remove the rear of the deck

Remove the two pins on each side of the deck to detach the rear cease from the mower.

five. Remove the front end of the deck

There is a small pin and bar that will need to be removed to detach the front end of the deck.

6. Remove the PTO cable

Commencement remove the pivot that secures the cable to the deck -- and then pull dorsum on the cable to release it.

seven. Remove the bound

Lastly, utilise your fingers to remove the jump near the PTO cable you lot just removed.

8. Slide the deck out

With the deck detached from the mower, yous're free to slide it out of the manner.

[Back to Top]
Removing the belts

i. Engage the parking brake

Doing this releases tension from the belts, making it easier for you to remove them.

two. Remove the battery

Use a pair of open end wrenches to starting time remove the negative terminal from the bombardment, and then the positive last. So pull the strap out of the way and ready aside the battery.

three. Remove the cradle straps

Simply pull these out of the way.

4. Remove the idler spring

Slide a rope into the spring hook to easily remove information technology. Reference the video for further detail.

5. Remove the manual pulley

Apply a screwdriver to lock the pulley in place, then use a wrench to remove the nut. And so pull the pulley off of the spindle.

half dozen. Remove the transmission belt

The belt should at present only slide off of the pulley.

7. Remove the motor pulley

Use a pipe wrench effectually the spindle to secure it, then use a socket wrench to remove the bolt. The motor pulley can at present be removed from the mower.

8. Pull the bulldoze belt off

Release the belt from the pulley "keepers" past lifting upward on the heart section of the pulley while lifting the belt upwards.

[Back to Top]
Installing the new belts

1. Install the new drive chugalug

Thread the chugalug through the frame and dorsum around each caster. Remember to slide the center part of the caster upward to make it easier.

2. Replace the motor pulley

Slide the pulley spindle dorsum into its original location with the belt already placed in the upper "keepers". So secure information technology with the bolt that was previously removed.

three. Install the upper-drive chugalug

First, thread it dorsum around the manual caster.

Then line up the teeth on the pulley with the teeth on the hub and secure it with the nut that was previously removed.

iv. Finalize the belt installation

Now simply thread the belt around the variable speed pulley and idler pulley.

5. Supplant the idler spring

Use the rope you used in the previous section to re-hook the spring and pull back it through the frame.

6. Replace the cradle straps

Place these back into their original locations.

7. Reinstall the battery

Ready the battery back into the mower, secure it with the strap, reattach the positive final, and so reattach the negative terminal.

 [Back to Top]
Remount the deck

1. Slide the deck dorsum under the mower

Make sure that the discharge chute is pointing out the right side of the mower.

two. Reinstall the PTO cable

Claw the bound to the end of the cable.

3. Reattach the leap

Then reattach the spring and secure information technology with the pivot.

4. Reattach the front of the deck

Place the bar back into the mounts on the forepart of the deck and secure information technology with the pivot.

5. Reattach the rear of the deck

Identify the bars back through the desired mounts and secure them with the pins.

6. Raise the deck

Use the bar command lever on your mower to enhance the deck back to your desired position.

[Back to Summit]
Conclusion If you lot've arrived at this point, your drive belts should be snugly installed and ready to become. Not only will repairing your products relieve yous time and money, it besides gives y'all the skills to tackle bigger projects in the time to come. Now get out in that location and put those belts to work past tackling your long grass! Don't forget to scan our huge inventory of lawn tractor spare parts. [Back to Top]
What Nosotros're About

Source: https://www.ereplacementparts.com/repair-center/article/12688/How_to_Replace_the_Drive_Belts_on_a_TroyBilt_Pony_Lawn_Tractor_.html

Posted by: woolfevently.blogspot.com

Share this post